发布时间 : 星期六 文章机械工艺夹具毕业设计75尾座体加工工艺及夹具设计更新完毕开始阅读4ad78c74647d27284b7351be
尾座体加工工艺及夹具设计
姓 名： 学生学号：
院（系）： 机电工程学院 年级专业： 级机械设计制造及自动化 指导教师： 副教授 助理指导教师：
摘 要
摘 要
本课题主要是设计某机床尾座体的加工工艺及夹具的设计，在设计中采用先设计该尾座体的加工工艺在根据加工工艺来选取夹具的设计的方案和夹具的具体设计；而设计的重点是夹具的设计。由于工件的孔17和14都要以底面做为基准加工，故首先得做出底面的加工夹具。由于孔17的精度要求高，和定位尺寸误差小，为保证孔的位置和加工准确性我们一定在加工底面的时间通过画线找出底面的加工余量。这样就可以更好的保证孔17的位置和加工精度！加工孔14的夹具其实就是在加工底面夹具的基础上加了一个45度斜度板。加工孔17的时间为保证相对于A和B面的平行度我们就得要准确的设计出以A和B面定为的夹具！还考虑到工件的圆度和圆柱度的误差小，我们设计的夹具就具有对孔17的夹具定位准确，和加工时间的震动小，那就得在孔17的附近找个定位加紧点！
关键词 加工工艺，夹具，尾座体，设计
I
ABSTRACT
ABSTRACT
This topic is mainly design that designs the tail a body of some tool machine to process the craft and tongses, adopting to design first in the design a body of that tail processes the craft at according to process the craft to select by examinations the tongs of the project of the design and concrete design of the tongs;But the point of design is the design of the tongs.Because the bore of the work piece 17 and 14 all want to face to be used as the basis to process with the bottom, past have to do a bottom to face first of process the tongs.Because bore 17 of accuracy have high request, and position the size error margin small, for guarantee the position of the bore and process the accuracy we certainly at process the bottom to face of time pass to draw the line to find out the bottom to face of process the amount of remaining.Thus can with better assurance bore 17 of position and process the accuracy!Process the bore 14 of tongs was in processing the foundation that the bottom faces the furniture to add one 45 degrees of gradient plank in fact.Process the bore 17 of time is opposite for assurance to run parallel with B face of in the A we have to design accurately with the AN and B faces to settle for of tongs!Return in consideration of a degree of the work piece and the error margin of the cylinder degrees are small, the furniture that we design have to the bore 17 of tongs fixed position is accurate, and process the vibration of time small, that have to in the bore 17 of neighborhood seek a fixed position to step up the point!
Keyword process the craft, tongs, a body of tail, design
II
目 录
目 录
摘 要??????????????????????????Ⅰ ABSTRACT????????????????????????Ⅱ
1绪论??????????????????????????1 2零件分析 ???????????????????????2
2.1零件的特点???????????????????????2 2.2工艺分析????????????????????????2
3工艺规程设计??????????????????????4
3.1确定毛坯的制造形成????????????????????4 3.2基面的选择???????????????????????4 3.3制定工艺路线??????????????????????4 3.4机械加工余量、工序尺寸及毛坯的确定??????????????8 3.5确定切削用量及基本工时??????????????????12
4夹具设计 ???????????????????????28
4.1问题的提出??????????????????????28 4.2夹具设计 ??????????????????????28
总结 ??????????????????????????33 参考书目 ????????????????????????34 致谢 ??????????????????????????35