发布时间 : 星期四 文章加工中心全部的报警说明 - 图文更新完毕开始阅读d6dc71e9a200a6c30c22590102020740bf1ecdfb
DC24V由ON/OFFRELAY控制 AC220V由K1A控制
1. A.Function=2Data=1Y72=33Mode=AutoY70=001Start=ST(T-code)
B.Function=2Data=4Y72=36Mode=JogY70=101Start=+x,-x(Jogonepitch) K2.1=0押Mag.CW-keyRun,放开Mag.CW-keyMag.Stopin-correctPOS.(连续运转)
K2.1=1押Mag.CW-keyRun,放开Mag.CW-keyMag.Stopin-nocorrectPOS.(onepitchstepbystep) C.Function=4Data=1Y72=65Mode=JogY70=101Start=ST
K13.2=1,K15.4=1JogMag.key-inManual,押主轴停止键1sec後放开Mag.Returnto1POS.D2=1 D.Function=4Data=15Y72=79Mode=JogY70=101Start=ST
K13.2=1,K15.5=1JogMag.key-inManual,押主轴停止键1sec後放开Mag.PMM000alarmP11#0=1 settingHOMEOK
E.Function=0Data=0xxxxY72=0Mode=JogY70=101Start=+x,-x K13.2=1押Mag.CW-keyRun,押Mag.CCW-keyStop错误
修正K13.2=1押Mag.CW-keyRun,放开Mag.CW-keyMag.Stop(注意D2不会更动)+X K13.2=1押Mag.CCW-keyRun,放开Mag.CCW-keyMag.Stop(注意D2不会更动)-X 用PMM#41=5JOG移动刀库取代MPG
D0=SpindleNO.,D1=WaittoolNO.D2=Mag.currentNO.D3=T-commandcodeNO 卧式APC 手动找寻O9000程式号码,且自动跳至自动执行G7.2(ST)=1 P6300#4(ESR)=1 P3202#6(PSR)=1 D100=90 D101=00 P6071=6(M6ARM换刀)O9001 P6072=100(M100APC自动更换)O9002 P6073=101(M101APCPA-IN更换)O9003 P6074=102(M102APCPB-IN更换)O9004 O9000(APC-MAN.)(D100=90,D101=00) #3003=1 G4
IF[1013EQ1]GOTO99(MLK) M98P9002 N99#3003=0 M30
O9001(M6-ATC)(P6071=6) #3003=1 G4
IF[#1008EQ1]GOTO99(TF=SP) IF[#1013EQ1]GOTO99(MLK) #130=#4003 #131=#4006
G91G30Z0 G30X0Y0 M6
M88(DOORCLOSE) G#130 G#131
M05(M05取消M03记忆) N99#3003=0 M99
O9002(M100-APC)(P6072=100) #3001=1 G4
IF[#1013EQ1]GOTO99(MLK) M71(APCCHECK) #130=#4003 #131=#4006 G91G30Z0
IF[#1011EQ1]GOTO2(ZP4OK) IF[#1012NE1]GOTO1(1=0.001Degree) M41 G91G28B0 M40 GOTO2 N1G91G28B0 N2M40 M72(PALLETUNCLAMP) G4X2. M74(PALLETUP) G4X1.
IF[#1009EQ1]GOTO3(PANOWIN) M76(PA->IN) G4X1. GOTO4 N3M77(PB->IN) G4X1.
N4M75(PALLETDOWN) G4X1.
M73(PALLETCLAMP) G#130 G#131 N99#3003=0
M99
O9003(M101-PA-in)(P6073=101) #3003=1 G4
IF[#1013EQ1]GOTO99 IF[#1009EQ1]GOTO99 M98P9002 N99#3003=0
M99
O9004(M102-PB-in)(P6074=102) #3003=1 G4
IF[#1013EQ1]GOTO99 IF[#1010EQ1]GOTO99 M98P9002 N99#3003=0 M99
EXEM100若停在M74(APC-UP)
因APC-UP(X11.2)APC-DOWN(X11.3)同时为1 把K11.0=1(解除APC-SOL自保) K14.0=1(解除APC-NOTREADY) K14.7=1(解除APC-OKENABLE) 关电再开使APC回位OK後K11.0=0,K14.0=0,K14.7=0 X12.1=0 M72APCUNCLAMP X12.1=1 M73APCCLAMP X12.1(接1.2NO) X12.1=0 M72APCUNCLAMPY7.6=1AIRCLEAN X11.7(接1.3NO)气密检知K14.1=1 X12.1=0 M72APCUNCLAMPY7.6=1AIRCLEANONX11.7=1(有风) X12.1=1 M73APCCLAMPY7.6=0AIRCLEANOFFX11.7=0(无风) 若X11.7没有0->1->0则AL1048AIRTIGHTALARM
K14.0=1(解除APC-NOTREADY)不可设1否则AL1048AIRTIGHTALARM不会出现 X11.7有风无1则AL1048AIRTIGHTALARMY7.6=1AIRCLEANON K14.2=1解除AL1048AIRTIGHT
DATABCD,BIN选择由PMCRPM设定D0~D1024Bit可作断电自保 COUNTERBCD,BIN选择由Ladder3设定
卧式位置开关保护
K15.2=1取消位置开关保护
3-AXIS皆入设定范围则保护+X.-X,-Y,-ZG132.0,G134.0,G134.1,G134.2=1 不保护+Y,+ZG132.1,G132.2=0 P6930,P6950=X(0,-700000)
P6931,P6951=Y(-500000,-650000) P6932,P6952=Z(-400000,-650000)